焊后热处理对2101双相不锈钢接头组织和性能的影响

作者:王皓;鲍亮亮;胡利方;孟庆森 刊名:热加工工艺 上传者:文静

【摘要】采用等离子弧焊+手工电弧焊工艺焊接经济型双相不锈钢2101,焊接接头分别在1050、1150℃固溶处理,利用金相显微镜、SEM、EDS和低温冲击试验等方法分析了接头组织、成分和性能。结果表明:2101双相不锈钢焊接时焊缝和HAZ易生成沉淀相Cr2N,使接头冲击韧性下降;1050℃固溶处理可以消除沉淀相,均衡两相比例,保证接头性能;固溶温度进一步升高,接头组织中铁素体含量增多,晶粒粗化,性能恶化。

全文阅读

Hot W orking Technology 20 1 4,Vo1.43,No.1 焊后热处理对 2101双相不锈钢接头 组织和性能的影响 王 皓,鲍亮亮。胡利方,孟庆森 f太原理工大学材料科学与工程学院.山西 太原 030024) 摘 要:采用等离子弧焊 +手工电弧焊工艺焊接经济型双相不锈钢 2101,焊接接头分别在 1050、l150℃固溶处 理。利用金相显微镜、SEM、EDS和低温冲击试验等方法分析了接头组织、成分和性能。结果表明:2101双相不锈钢焊接 时焊缝和HAZ易生成沉淀相 Cr2N,使接头冲击韧性下降;1050℃固溶处理可以消除沉淀相,均衡两相比例,保证接头 性能;固溶温度进一步升高,接头组织中铁索体含量增多,晶粒粗化,性能恶化。 关键词:2101焊接接头;固溶处理;相比例;沉淀相;冲击韧性 中图分类号:TG441.8 文献标识码:A 文章编号:1001-3814(2014)01-0058—04 Efect of Heat Treatment After W elding on Microstrurcture and Properties of 2101 Duplex Stainless Steel Welded Joints WANG Hao,BAO Liangliang,HU Lifang,MENG Qingsen (Materials Science and Engineering,Taiyuan University of Technology,Taiyuan 03024,China) Abstract:PAW +SMAW process was used in the welding for UNS$32101 economical duplex stainless stee1.After solution treatment at 1050 and 1150℃,the weldedjoints were investigated by OM,SEM,EDS.The low temperature impact test can determine the microstructural evolutions and properties.The results show that the precipitation phase of Cr2N easily precipitates in the weld and HAZ of2101 weldingjoints,which result in the reduction in impact toughness.1050℃ solution treatment can eliminate the precipitates,balance the ratio of two phases,ensure the optimal joint performance.As the solution temperature is increased furtherly.The ferrite content increases and grain coarsenes in the welded joint,which can result in the perform ance degradation. Key words:2101 weldedjoint;solution treatment;phase ratio;precipit

参考文献

引证文献

问答

我要提问